Pipe insulation is one of the important components of energy conservation. Thanks to thermal insulation materials for pipes, it is possible to reduce heat loss and save resources and energy. Pipe insulation Energoflex in the domestic market occupies a leading position.
Types of thermal insulation materials
There is a wide variety of thermal insulation materials for the pipeline. Each species has individual characteristics that must be considered when choosing. For the insulation of the pipeline are used:
- liquid products;
- polyurethane foam;
- polystyrene foam;
- basalt cotton wool;
- fiberglass materials;
- foam material.
Liquid thermal insulation is in great demand due to the following characteristics:
- Due to the liquid consistency, the building material can be applied to hard-to-reach and uneven places, hidden areas.
- Installation, in comparison with laying other types of thermal insulation, takes less time and does not require special training.
- The more layers of thermal insulation applied to the surface of the pipeline, the better heat will be retained.
The composition is applied using a spray or a special brush.
Fiberglass insulation is also very popular. The peculiarity of the material is light weight, the structure does not rot. Therefore, mineral wool is isolated by pipelines passing on the street. Installation is carried out as follows: the pipes are cleaned and degreased, then wrapped with an insulator and securely fixed with a knitting wire. To enhance protection against harmful environmental influences, they are additionally insulated with foil or roofing material.
Basalt wool is an insulating material that is made in the form of plates and cylinders. It does not leak moisture, has increased strength and fire safety. Installation is easy, no special skills required.
Technical characteristics of a tube from the made foam polyethylene Energofleks
Energoflex - insulation for pipes, which is a flexible thermal insulator. Use building material to warm the pipeline and any other surfaces.
A heater is made of high-pressure polyethylene, which is extruded and then foamed. The structure of the starting material is porous, the cavities are filled with air. Thanks to this, it was possible to achieve impeccable heat-insulating properties.
Energoflex thermal insulation is available in the following types:
- Hollow tubes that are worn over the tubes. The diameter of the product ranges from 18 - 160 mm. The material can be worn entirely on the metal structure or cut along and then glued seams. The latter option is used if the pipes are not insulated during the construction of the pipeline, but in the process of its modernization.
- Rolls. They can be foil and not. Foil insulation is most in demand. Such material can be used for insulation of floors and other complex, inaccessible systems.
- Pipe thermal insulation Energoflex can also be made in the form of sheets. The material is a flexible plate of a thermal insulator, which is used to ensure the operation of fittings or sections of pipelines with large pipe sections.
-
- Roll
-
- Tubular
-
- Sheet
Energoflex thermal insulation material is also produced in the form of self-adhesive tape and plates.
Material Specifications:
- excellent quality of organic thermal insulation - indicators fluctuate around 0.038-0.039 W / m * s;
- extensive scope and large size range;
- permissible temperature ranges from -60 to +90 degrees Celsius;
- with proper installation and compliance with the operating rules, the duration of use is at least 25 years;
- resistance to chemicals of any nature - high-pressure polyethylene does not react with oils, saline solutions, acids and alkalis;
- excellent water-repellent properties - the porous structure absorbs no more than 3.5% of the moisture volume.
When choosing a heat-insulating material, it is important to consider that its Enerflex products are susceptible to direct sunlight.
Installation of the heat-insulation tube Energoflex
Thermal insulation pipe Energoflex does not cause special difficulties in installation. Installation Algorithm:
- The surface of the pipe is pre-cleaned and degreased.
- Carefully lay the heat insulator, there should be no exposed pipe sections.
- First you need to isolate the elements of the fittings and curved sections, then straight lines of the pipeline.
- A special adhesive base is used to connect the parts.
- The pipeline should dry well during the day, after which the system can be started.
If all work has been carried out in accordance with the instructions, the material will last a long time, preventing heat loss and protecting the pipeline from the harmful effects of corrosion.
Tools and fixtures
Before starting construction work, you need to prepare all the necessary working tools. To carry out the work you will need:
- pencil or pen;
- special miter box for cutting corner wedges and mounting angle of rotation;
- smooth spatula;
- a knife with a long blade (about 300 mm) for cutting pipes with a large cross-section and rolled material;
- short knife for cutting small diameter pipes (about 70 mm);
- roulette;
- construction line;
- brush for applying special glue to the surface;
Often forget about annular punches, which are used for making holes in the insulating sheet.
Bonding thermal insulation Energoflex
Before applying the adhesive mass, mix it thoroughly. The best option is to use the substance in a tank with a capacity of about 0.5 liters. Glue is applied with a thin even layer on both glued surfaces. These areas join 5-7 minutes after applying the adhesive mass. If the adhesive has dried during this time, it is applied again.
Work can be carried out at an ambient temperature of at least +17 degrees Celsius, the most optimal +20 degrees. If the adhesive mass has thickened, you can dilute it with a solvent from the manufacturer Eneroflex.
Thermal insulation for pipes Energoflex has all the necessary quality certificates and meets international standards. To acquire the required amount of materials, you must first measure the length of the highway, taking into account details, bends and joints.
